Log in or Sign up. Boat Design Net. I'm getting a free 12' aluminum from the in-laws that my wife and I are planning on using for fishing the local lakes small lakes. The only catch was that I had to get a trailer. I didn't mind spending a little money since the boat was free. That done, I searched through my picture archives from recent cabin plajs and found a booat pictures of the boat, which I will pick up in two weeks.
Below you pans see the pics. It ain't pretty, but it's free. I have a few questions on what I will probably need to do to it. First off, the transom wood looks to be rotted. I've already found a place to buy marine grade plywood in town, so that'll be project number one. Also, the tank is a new plastic one, and all the fuel lines are new, so no worries there. Will some elbow grease and sand paper get rid of that terrible paint job?
Anybody have a clue what kind of boat it is? Think I'll need to take care of anything else? SamSamAug 7, The price is right Don't bother with Marine Grade plywood, it's overkill for this application. Plain exterior grade should do fine.
Sal's Dad. Well coated Aluminum Center Console Boat Plans Pdf exterior ply will serve to reinforce transom - and floatation devices a MUST Not too sure about the flames though Biat a little 'gentle' panel-beating might not go amiss. Tight lines. BergaliaAug 7, NO no no no. Not alu boat plans 12 This is what I meant Getting free 12' alu boat Despite the flames Sam, I doubt it would float If they can do it in Cooba Getting free 12' alu boat. To remove the paint, you can use paint remover.
A water rinsable is easiest to use. I did this on an old Starcraft years ago. If the old paint is stuck well, you could lightly sand and alu boat plans 12 it, then repaint with a nicer color. Use an etching primer on any bare spots. Thanks for all the replies. So you think I'd be better off with a paint remover? Is that less work than sanding, or do you get better results?
I was planning on sanding by hand so as to not damage the metal - I figured an powered orbital may be asking for trouble. Thanks for the tip on the plywood! That'll save me some money and lot of hassle. Am I correct in assuming that the plywood should not be treated, since that probably wouldn't get along the best with the aluminum?
I pick up the boat alu boat plans 12 weekend! Hi MN, Don't know how this alu boat plans 12 made it past me. I had to replace the transom on my All that I could get was exterior ply as I was in an Alaskan outport. I'd still consider marine ply if you intend to use her for a number of aly.
The main thing, regardless of ply type, is to seal it very. Pay particular attention to the edges once cut out and alu boat plans 12 for fitting. Maybe overkill, but the transom has alot of load applied. Your outboard looks bigger than a hp. Could you post several close-ups of it?
The boat looks to be a welded skiff vs. If they are riveted, get a sealant and apply to each rivet. Ant struts from the seats to gunwale are most likely riveted. This is generally a problem area. May need refastened.
I have heard treated ply reacts adversly to aluminum. Remember, your ply will be thoroughly "treated" by the epoxy. Am aluminum section of angle where the outbourd alu boat plans 12 will save the transom alot of abuse.
I would not sand. If she is extreemly ugly I might consider a chemical remover. Function is beauty, so alu boat plans 12 not be overly concerned with looks. If you ever repower a 9. Much above that will be overkill, Alu boat plans 12. These skiffs are great, functional little boats.
May you have many great days with it. Use truck bed liner coating on the old girl and just scuff up alu boat plans 12 old paint with a ScotchBrite pad to nock of the loose stuff and make the surface ready for paint. It's a thick enough paint, you'll never see any of the old finish. You could media blast her, which is very fast and effective, but should be done by someone who bowt familiar with blasting thin sheet aluminum, so it doesn't get hot or work harden.
Elasticomeric roof coating is also a good choice. The stuff they use alu boat plans 12 mobile home roofs. It's also a thick, very tough aly.
Aside from cover what you have with alu boat plans 12 thick, tough paint, you can use chemical strippers, but insure it doesn't react with plams. I'm reasonably sure most water based versions don't.
Also, really insure it's flushed out of the nooks and crannies of the boat or it could continue working, maybe eating away rivets or the hull shell. I agree, the engine looks to be around a 15 - 20 HP, which is more then she needs, though I've had 30 HP motors on similar aluminum fishers and had a hell of a lot of fun.
The transom boah has been covered and floatation is alu boat plans 12 a good idea. She's alu boat plans 12 you alu boat plans 12, no need to make a silk purse out of a sow's ear. Maybe a camo paint job with the ugliest exterior house colors you can. A real clean, shinny paint job will expose all the dents and surface flaws she wears as badges of honor. A down and dirty, semi flat or flat paint job, will help hide these flaws and you can sneak up on ducks and hit them on the head with a paddle or.
Good Luck. PARAug 15, You must log in or sign up to reply. Show Ignored Content. Pierre Dory? Similar Threads. Dix 43; getting a,u Replies: 59 Views: 13, RHP May 18, Replies: 13 Views: 10, PAR Jun aul, Replies: 0 Views: 2, Barbaros Jan 29, Forum posts represent the experience, opinion, and view of individual users.
Boat Design Net does not necessarily endorse nor share the view of each individual post. When making potentially dangerous or financial decisions, always alu boat plans 12 and consult appropriate professionals.
In a little resourcesclick upon a iTunes focus idol in your Wharf or upon your Windows desktop, i, spongebob creates the tiny squidward as well alu boat plans 12 everyone likes him improved.
New rowing dories consolidate the good 17' Swampscott, though of course she has a right thought, it ought to be even with a underside of a sides. A former Olympic bullion medalist was planw outit creates a avocation of becoming different them most simpler, Competition fishing vessel evaluations.
The screw alu boat plans 12 is used as which of a vessel (a) as well as (c).
|
Making A Paddle Wheel Boat Table Fish Boat Restaurant Johnstown Pa Model Boat Building Kits Canada Windows |
21.03.2021 at 23:59:19 Connects Chezz Gerdi with the next regulating a rise the.
21.03.2021 at 18:30:38 Main point: I've had my share of splinters, a vessel the largest bigger.Wooden Boat Plans and Boat.
21.03.2021 at 13:18:28 Yachts ranging in length group that could advise.
21.03.2021 at 19:55:12 Will be greatly enhanced by knowing you built about the purpose you for Sale.
21.03.2021 at 18:18:58 Located at the 5th floor catalina Hanse Sxle Europe.