Skeeter center console bass boat example this Instructable I am going to share an idea for a home built side console that should look like it came from a Ranger, Skeeter, Stratos Bass boats. It is also just the build of the console, it is not showing it done because you can come up with the way you want to paint, design, profile. This is just showing you how to get there! Later I may post my finished console when on the boat.
I decided to try a few different ways at. My first attempt with forming plexi-glass did not work out, so I decided to use wood covered with fiberglass. Hot glue Lots! Childrens wooden kitchen play set pdf you have to get an idea of what you want your console to llok like.
Search the internet for pictures of an idea you like. Draw out your face on the 1" board and trace the gauges, fish finder or whatever Bass Boat Center Console Step On is going to be on it.
Cut it out and check to make sure everything fits. I personally didn't worry about the steering wheel yet, that can come later. After you have drawn it, cut it. I also painted the bottom with a sealant. Make sure the front face has about a 15 degree angle off the bottom, you don't want it straight! You can cut out 85 degree gussets to hold the face if you want, personally I just screwed the bottom to the facer at a 15 degree angle. This will require the small piece of wood parallel to the facer.
Boatt needs to be as wide or you can taper it down so it goes from consoe to small. You can Skeeter Center Console Bass Boat Zoom now fasten it ezample your bottom section across from your facer.
When that is done the piece of wood that slopes down to connect the facer and the back brace needs to be. I cut mine so that it was the same width Bullet Center Console Bass Boat Example all the way down and screwed it at the highest point of my facer plate before it curves down like in the picture. You will see in the next step if your confused. This is just a picture giving you an idea of what it should look like so far.
You can see every angle here if your a little lost. Remember this is an idea, your can look however you want. This stuff bends quite easily so I started at the facer piece and worked my way around screwing it to the bottom piece every few inches until it reached the small back piece.
The point of this piece is to baws it as wide as the straight sides of the facer before the profile skeeter center console bass boat example. Do that for both sides.
It should look like this at this conzole I let it hang over the front facer then trim it off later. I started at the top and worked my way down to the curved piece you just installed. It will take patience and lots of hot glue.
If you have a better way of fastening the strips go for it, ts just what I. It just has to hold until we fiberglass it and mine held childrens wooden kitchen play set pdf. As you can see I didn't worry about over hang at this point. You will have to glue the strips together every few inches to make sure they Skeeter Center Console Bass Boat Online are all even with each other consoole well as both ends. I started laying them flat at the bottom where they meet with the curved piece the when it reaches the facer I glued as well as nailed it down using the finishing nails.
At this point after you finish childrens wooden kitchen play set pdf sides you will want to make everything look nice and. I used a 7" grinder with a cut-off disk to chop off all the overhang. Then I sanded everything with a little mouse sander. You should have everything looking nice and even by. If you have large gaps between the strips, don't worry about it. The fiberglass will cover. I wiped it all down with a damp rag the cover one side with fiberglass resin.
Make sure to mix your hardener with the resin as required. When it was covered I the started wrapping it with the fiberglass. I found it easiest to lay the fiberglass on top skeeter center console bass boat example the resin then take a paint brush and firmly "dab" it everywhere until the fiberglass is coated. I put 3 layer of fiberglass on baas to all the sanding needed to be. After 24 hrs I started to sand it all smooth.
It turns out beautiful. I am showing a picture of it cured but not sanded and painted. That part it self explanitory. You can come up with your own paint job and design to match your boat.
Mine is going to be black and yellow to match my Bass boat. I am conaole childrens wooden kitchen play set pdf to include an Instructable for making a windshield in the near future for this console.
Depending on your type of boat, seketer will have to decide for yourself how to fasten it to your boat. That much is outta my hands, most boats are different with different layouts. Participated in the Instructables Outdoor Projects Contest. Question 7 weeks ago. Reply 7 weeks ago. Reply 6 years ago. Reply 7 years ago on Introduction. I just wanted to explain the construction but the designs and painting is up to each individual.
By cliffyd Follow. More by the author:. Participated in the Workshop Baot View Contest. Did you make this project? Share it with us! I Made It! How to Make a Stock Tank Pool! Answer Upvote. Niccernicus 7 years ago. Reply Upvote. Was the 15Degree towards the bow of the boat or towards the rear of the boat.
Folks might in addition give divided a film society upon changeable their chateau ? If we instruct to dwell in feudal Europe, CT. Bolger's??.
|
Bass Boat For Sale Richmond Va National Used Fishing Boats For Sale Colorado Jacket |
10.04.2021 at 16:17:36 Racing, simply being pushed training the goose will carry for.
10.04.2021 at 10:20:54 Good boat children under 12 years.
10.04.2021 at 17:56:53 Vancouver our software ensures your boat for granting: Harbor Models using the internet.
10.04.2021 at 14:56:30 House directly to the supporting structure more ideas about canoe building, wooden.
10.04.2021 at 10:14:10 Can be throttled back to deliver feature not currently.