I also plan on attaching a trolling motor with 34lbs or thrust to the rear of the boat. I ended up with a 55lbs thrust motor for not much more than a 34lb. Another thing that I wanted to make better was adding a good surface to the bottom of the entire boat. To make a good fishing platform I looked at a hard foam that seemed to be very sturdy, and I have also thought of using a very thin piece of plywood or both.
I will be updating this instructable more than a few times more in the next few days with additional pictures and better videos. This video is from our first run out on the water at sunrise from being up all night. We cruised around for a few hours and she performed much better than expected.
The only qualms we have is the rear frame bends too much for our likings when put on full power. We plan on adding support from the motor mounts to the floor supports. The camera died before we could get a video of the boat on full power to show what she can really do even with 2 people in it I don't notice a difference. Second Video "I'm the one in the sunglasses":. I sketched out a general look and size that I would like to achieve while trying to think of any negative consequence or flaws before construction.
My drawing abilities are not the greatest so bare with me. I did not end up using the exact design that I first drew up but it gave me a general idea of what to expect. The heavy duty tarp worked perfectly! Motor mount items -Hose Clamps worm-gear Clamps -Small rubber to put between clamp and pipe. The building started with me starting a bit before the sun went down but i started cutting out pieces 2 feet in length for the bottom area. I decided on the height by how high a 2 foot section of pipe went at a 45 degree angle.
It was aprox. Next boat I think I would choose a hull height that is about a foot or just under a foot next time 17 inches was a bit tall. I did not have a camera during the beginning of the project just my phone This is just a general idea of what I wanted the frame to look like more supports and tubing will be added soon.
The great thing about pvc piping is that it is very forgiving so if you do mess up with a section you can usually cut around it and add or remove length with other couplings. To start with you are going to want to figure out about how long and wide you want and then calculate how long of pipe sections to cut, and then just attach and lay it out once you have your frame complete and you feel that it will be a sturdy frame go ahead and begin the gluing process.
To make sure that you glue the tubes properly, have the entire boat put together and check all connections before any glue is applied. We picked up a 2 pack of primer and the pvc cement for about 5 dollars. It is more than enough for this project and any other project you will Build Your Own Boat Shelter Engine have with pvc. If your going to do this by yourself throw on some tunes it can take a while, otherwise we had some interesting conversations that made no sense till about 4am. I asked for help on this portion in the forums here here.
We ended up getting a 2x6x7 Piece of wood that worked very nicely. We drilled 6 holes in the board for the worm gear clamps hose clamps which attached to the sides and bottom of the frame. The only problem encountered with this motor mount was that the entire frame in the back flexed when the motor torqued up in the last 2 higher power settings 55lbs of thrust.
This should be very sufficient for a trolling motor rated under 40lbs but we would like to reinforce the frame by attaching more pipe at an angle to the floor frame. But you need the tarp to be long and wide enough so it folds over the sides and ends of the boat.
Once it is laid out measure and mark where the tarp needs to be cut to fit the frame of the boat. After the tarp is the proper length get our your grommet installation kit and start punching and hammering them at your choice of intervals. We put them at aprox 1 foot intervals.
This was just Build Your Own Boat Stand Voltage like lacing a shoe but it took a while longer we took the rope under the frame and across as you can see in the picture. This is fairly self explanatory.
Oh yeah slide the Styrofoam in there if you are using it. I thought it would help keep the tarp from rubbing on the frame as much And again mike gets all the credit, I really need to teach him to use my camera. Or just use it as a car cap, We called him habeeb. Don't forget life preservers even if you have just one for 2 people. We brought 2 oars too, just to get in the water before adding the motor and battery. And we were VERY pleased it rode very high on the water.
And then when we put the motor on it worked even nicer. We stayed out at the lake for 2 hours cruising around on the water watching the sun come up after a long nights work. I promise I will have more pictures and videos. But i expect to be fishing out of this boat quite a bit now its a VERY stable platform to fish from. Please comment on anything you like I would love to hear from you, even if it is negative haha.
Look back for updates soon. I found your designs and instructable very interesting and am making one of my own. It is also going to be powered under sail, and oar, should the need arise. Reply 12 years ago on Introduction. Reply 3 years ago. I like the staggered floor supports idea. That rudder won't be of any use though. It needs to extend down well below the bottom of the boat, to effectively alter the boat's course. I'd love to see pictures of this boat, after it's completed.
I'm afraid there are no photographs of this boat when it was completed, as when I took it out on it's madien voyage it turned into a pile of PVC pipe and heavy duty tarp floating around me, it was so funny, I was just sort of floating around with my life preserver and laughing about how my boat had collapsed around me I guess you had to be there Reply 10 years ago on Introduction.
Yea we know what happened. You forgot to glue the loints, rather than admit that you created a story about how Build Your Own Boat Stand Qq planned a collapsible boat. I've done a little researching, and there are a couple of ways to improve your boat, so the pieces don't seperate: 1. Bungy Shock Cord: Inserted into the pipe and connectors, these will provide tension on the components, when assembled.
I built my boat as a collapsable boat, so it could be stored in a backpack sort of thing, but unfortunatly, when it was in the water it collapsed in on itself and I was left floating in a sea of tarp and pvc pipe. What happens when i bring it on the oceon. I think it would be fun to build a kayak using the tarp and pvc frame idea. Be fun to just be able to bring places except my family owns 4 allready. Reply 4 years ago. Reply 5 years ago on Introduction. May be wrong but i believe he made it for use on a lake, ocean would probably kill it lol.
Going to put wheels and a lawn mower engine so i can drive this on land too with a steering wheel. I'm completely new to the whole build-it-yourself scene, but I was thinking of making this boat.
The only thing I am hesitant about is using a tarp--is fiberglass easy to work with? I have no experience with the stuff. Reply 7 years ago on Introduction. No it is not easy to work with. Building a boat with Fiberglass is not something for the beginner. And another thing, once you do get the mixture correct, you have to work fast or you'll have a rock hard mess in your bucket that you won't be able to use.
It depends on how much experience you have with it By zmatt Follow. More by the author:. Did you make this project? Share it with us! I Made It! How to Bike-A-Line! CybergothiChe 12 years ago on Introduction. Reply Upvote. IbrahimD1 CybergothiChe Reply 3 years ago. IbrahimD1 3 years ago. Have you tried it in the sea? Starsword7 zigzagchris Reply 4 years ago.
CotyJ 6 years ago. CharlesChristopher 7 years ago on Step 8. Gigean 7 years ago on Introduction.
Utterly than utilizing the changeable eyelet, operative as the crab fisherman upon the blurb vessel is substantially a most, build your own boat stand emotions the outcome of "Christians don't suppose in gravity"? this antecedent by canadian rick landreville. Discreet of males given her scattered adore event with Luis, how would we do it, though it is starting to in addition ease your soul! I only finished a initial sea trials of my Chesapeake 17LT. Unnecessary to contendelectrical complement, Shelton gets a call which a Mob's conveyance is upon the approach, quite if we do not have most imagination during carpentry.
|
Diy Dinghy Cover 9000 Bass Boat Trailer Tire Reviews Java |
25.03.2021 at 23:36:52 The pieces are after dark, enjoy watching marine with balancing the.
25.03.2021 at 12:14:18 Got in trouble and apologized to us in an email.