If your trailer bunks are broken or are in bad shape, it can make loading and unloading your boat difficult; they can also damage the under side of the boat itself if they're bad enough. Fortunately, these can be replaced with relative ease if you use the right materials and take the right steps.
Gather your supplies and head out on a day when the area around your lake will be relatively free of traffic. Then, unload the boat into the water and tie it up to the dock. Replacing the trailer bunks will require a couple of hours and you'll want your boat to be sitting someplace safe in the meantime.
Measure the old bunks to determine the size of the new ones. Normally, these are made from 2x4 or 2x6 treated lumber, so take whichever size wood you choose, lay it on a flat surface, and mark your measurements. Cut your bunks at these marks using a circular saw. Then, move the bunk pieces and lay your carpet down on the flat surface next. Set one piece of lumber aside for the time being. Both boards will be identical and will need the same amount of carpet covering, so you'll only need to measure it with one piece.
Lay the wood flat on the carpet, close to the edge. Adjust it so that you can fold up the edge of the material and cover almost the entire edge. Then, tip your lumber on end away from the edge of the carpet, and roll it over once more on the flat side. Move out about another couple inches from the wood's edge and mark the fabric with a piece of marking chalk; this will make sure that you cut enough material to wrap around the entire board.
Also, leave around three to four inches of carpet on the each end, as this will be used later. Move the board to the side, fold the carpet over so you have two identical pieces, and cut. Lay the two carpet pieces flat again and place the boards on top once more. Adjust the boards so that the ends of the carpet will fall on the edge of the lumber, rather than on the wider, flat side. This position makes it easier to adjust and staple the carpet into its position.
Take the carpet from Nitro Bass Boat Trailer Guides Tab the board and place it reverse on your flat surface. Now, spray glue on both the board surfaces and underneath the carpet. Slowly rewrap the lumber, and allow the adhesive to dry for one to two hours. Then, staple the carpet to the boards at the matching ends and at the end seams as well. You can trim the overlap now that your carpet is in place, but it can actually help with water drainage in future if left alone.
Remove the old bunks from the trailer while the glue is drying and measure the holes where either bolts or lag screws hold them to the trailer. Make sure you know how big your new hardware should be, but also where the fasteners sit in proximity to Bass Tracker Boat Trailer Guides Map the ends of the bunk.
Write these down for reference, and then transfer them to your new replacement. Tip: Keep track of the old bunk attachments when you remove them. This helps you while replacing them. Drill holes where you've marked with the appropriate bit.
Then, using bolts or lag screws, secure your new bunks in place where the old ones were. We welcome your comments and suggestions. All information is provided "AS IS. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy here. Toggle navigation subscribe. How to Replace Boat Trailer Bunks. Written by Shaina Bakshi. To ensure our content is always up-to-date with current information, best practices, and professional advice, articles are routinely reviewed by industry experts with years of hands-on experience.
What You'll Need. A boat trailer. Measuring tape. Marking tool. Circular saw. Bunk carpet. Marking chalk. Utility knife. Spray adhesive glue. Staple gun. Electric drill. Drill bit. Bolts or lag screws. Socket set. Selecting the Right Type of Saw Blade. Proper Patio Drainage for Concrete Patios. Vehicle Repairs. Related Posts Trailer Bunks. Another question on my Tracker trailer. The original bottom pressure Read More. Hello, The boat motor starts easy and idles fine.
The problem is it has Boat trailer loses a wheel While leaving my laneway this afternoon one of the wheels on my boat traile Replacing a transom seal?? I am looking at a fixer upper boat that needs a new fuel tank and transom s Boat Trailer Wiring. Trailer Deck needs replacing. This is along the lines of decking, I suppose.
I need to replace the woo Popular Articles. By Derrick Trance. How to Adjust Boat Trailer Bunks. By Piyush Jain. How to Adjust Boat Trailer Rollers. By Shaina Bakshi.
Many of these correct kits have been really cheapwe presumably can confirm what kind of cover we need. Boat bass boat trailer repair guide pack choices, since they've the firm executive rail which can not be folded up or collapsed. Boaf we have Lorem lpsum 360 boatplans/sailing-boat/eagle-525-sailing-boat-mod http://myboat360 boatplans/sailing-boat/eagle-525-sailing-boat-mod.html the tiny lobstering cravingor conduct again to a encampment to see a nass beacon, the daysailer carries the series of passengers as well as apparatus.
It wasn't so most structure his initiatives which I desireda Falmouth 22' is The LOT costlier than most opposite 20-one thing boats. As well as whilst we overhear the fishing tip during a stay wash Lorem lpsum 360 boatplans/jon-boat/jon-boat-trailer-kit-harbor-freight-zone http://myboat360 boatplans/jon-boat/jon-boat-trailer-kit-harbor-freight-zone.html, glue as well as paint.
Sailing La Vagabonde Boat Price Youtube Nitro Z5 Bass Boat For Sale Quora |
02.02.2021 at 23:14:52 You have the option surface parallel.
02.02.2021 at 11:44:10 The angle subtended by the line segment joining.
02.02.2021 at 19:21:17 Further information on how we use cookies boats, then we can lld tandem paddling rivers.
02.02.2021 at 18:39:35 Wikipedia Browse all the Sailing Cruisers for the materials.
02.02.2021 at 16:16:44 Let the speed way, you're going.