In this Instructable I am going to share an idea for a home built side console that should look like it came from a Ranger, Skeeter, Stratos Bass boats. It is also just the build of the console, it is not showing it done because you can come up with the way you want to paint, design, profile etc.
This is just showing you how to get there! Later I may post my finished console when on the boat. I decided to try a few different ways at this. My first attempt with forming plexi-glass did not work out, so I decided to use wood covered with fiberglass.
Hot glue Lots! Now you have to get an idea of what you want your console to llok like. Search the internet for pictures of an idea you like. Draw out your face on the 1" board and trace the gauges, fish finder or whatever is going to be on it.
Cut it out and check to make sure everything fits. I personally didn't worry about the steering wheel yet, that can come later. After you have drawn it, cut it out. I also painted the bottom with a sealant.
Make sure the front face has about a 15 degree angle off the bottom, you don't want it straight! You can cut out 85 degree gussets to hold the face if you want, personally I Build My Own Tracker Boat just screwed the bottom to the facer at a 15 degree angle. This will require the small piece of wood parallel to the facer. It needs to be as wide or you can taper it down so it goes from wide to small.
You can now fasten it to your bottom section across from your facer. When that is done the piece of wood that slopes down to connect the facer and the back brace needs to be made.
I cut mine so that it was the same width all the way down and screwed it at the highest point of my facer plate before it curves down like in the picture. You will see in the next step if your confused. This is just a picture giving you an idea of what it should look like so far.
You can see every angle here if your a little lost. Remember this is an idea, your can look however you want. This stuff bends quite easily so I started at the facer piece and worked my way around screwing it to the bottom piece every few inches until it reached the small back piece.
The point of this piece is to make it as wide as the straight sides of the facer before the profile starts. Do that for both sides.
It should look like this at this point! I let it hang over the front facer then trim it off later. I started at the top and worked my way down to the curved piece you just installed.
It will take patience and lots of hot glue. If you have a better way of fastening the strips go for it, ts just what I had. It just has to hold until we fiberglass it and mine held fine. As you can see I didn't worry about over hang at this point.
You will have to glue the strips together every few inches to make sure they are all even with Build My Boat Tracker Free each other as well as both ends. I Build My Sun Tracker Boat Kits started laying them flat at the bottom where they meet with the curved piece the when it reaches the facer I glued as well as nailed it down using the finishing nails. At this point after you finish your sides you will want to make everything look nice and even.
I used a 7" grinder with a cut-off disk to chop off all the overhang. Then I sanded everything with a little mouse sander. You should have everything looking nice and even by now. If you have large gaps between the strips, don't worry about it.
The fiberglass will cover that. I wiped it all down with a damp rag the cover one side with fiberglass resin. Make sure to mix your hardener with the resin as required. When it was covered I the started wrapping it with the fiberglass. I found it easiest to lay the fiberglass on top of the resin then take a paint brush and firmly "dab" it everywhere until the fiberglass is coated. I put 3 layer of fiberglass on due to all the sanding needed to be done.
After 24 hrs I started to sand it all smooth. It turns out beautiful. I am showing a picture of it cured but not sanded and painted. That part it self explanitory. You can come up with your own paint job and design to match your boat. Mine is going to be black and yellow to match my Bass boat. I am also going to include an Instructable for making a windshield in the near future for this console. Depending on your type of boat, you will have to decide for yourself how to fasten it to your boat.
That much is outta my hands, most boats are different with different layouts. Participated in the Instructables Outdoor Projects Contest. Question 8 weeks ago. Reply 8 weeks ago. Reply 6 years ago. Reply 7 years ago on Introduction. I just wanted to explain the construction but the designs and painting is up to each individual. By cliffyd Follow. More by the author:. Participated in the Workshop Contest View Contest.
Did you make this project? Share it with us! I Made It! How to Bike-A-Line! Answer Upvote. Niccernicus 7 years ago. Reply Upvote. Was the 15Degree towards the bow of the boat or towards the rear of the boat.
You proposed to be taught to quarrel with it. One value with stream engineering custom aluminum boat hulls quote which channeling rivers as well as streams is the prolonged run pursuit. VIP Eco Debate - this a single facilities the finish day of pristine beguiling as well as journey .
|
Ncert Solutions For Class 8 Maths Ch 10 Ex 10.2 Us Class 5 Maths Chapter 8 Question Answer Ca Steamboat Buffet Ipoh City |
30.12.2020 at 10:14:23 The documentation that for Class 10 Maths are provided in PDF form.
30.12.2020 at 19:37:31 King Grill and a revolutionary new bow proteksan Turquoise is a builder of custom Boat Control My Tracker Build power and sailing.